Posts Tagged RHEL
Recently, I got around to installing Oracle Linux 6 (RHEL 6 clone) on a machine in order to experiment with kvm. The machine I installed it on is an Intel Core 2 Duo 6400 with 4 GB of RAM. Intel Virtualization Technology (VT) is present in this chip, and enabled in the BIOS. I am running the server headless.
At install time, I chose the ‘virtual host’ option.
Setting up a bridge ‘br0’ in order to enable VM bridged networking:
Oracle Linux installs a default bridge virbr0 that is useful if you want to configure the VM to use ‘host only’ networking. I wanted a bridged network VM, i.e. the VM’s virtual interface should appear on my physical network just as any other machine would. There are a few steps that I need to do in order to enable this:
- Create a new bridge ‘br0’ and assign it the static IP address that used to be associated with eth0.
- Make the physical network interface ‘eth0’ be an uplink port to this bridge ‘br0’.
The assumption here is that the physical network card in the system is ‘eth0’. If you have ‘eth1’ connected to the network, make the corresponding changes to the setup described. Another assumption here is that at the end of the Linux install, ‘eth0’ has the static IP address 192.168.1.201/24 with gateway 192.168.1.10.
First create a new file /etc/sysconfig/network-scripts/ifcfg-br0 with the following contents:
DEVICE="br0" TYPE=Bridge NM_CONTROLLED="no" ONBOOT="yes" BOOTPROTO=static IPADDR=192.168.1.201 NETMASK=255.255.255.0 GATEWAY=192.168.1.10
Next, delete the old ifcfg-eth0 file, and create a new one with the following contents:
DEVICE="eth0" NM_CONTROLLED="no" ONBOOT="yes" BRIDGE=br0
Setup /etc/resolv.conf to point to the free google DNS Servers:
nameserver 18.104.22.168 nameserver 22.214.171.124
Reboot the system. When it comes up again, the bridge br0 should have the IP address, and eth0 should be an uplink port on the bridge, as shown below:
br0 Link encap:Ethernet HWaddr 00:1C:C0:07:20:70 inet addr:192.168.1.201 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe07:2070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:69422 errors:0 dropped:0 overruns:0 frame:0 TX packets:38962 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8360996 (7.9 MiB) TX bytes:9988797 (9.5 MiB) eth0 Link encap:Ethernet HWaddr 00:1C:C0:07:20:70 inet6 addr: fe80::21c:c0ff:fe07:2070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:69433 errors:0 dropped:0 overruns:0 frame:0 TX packets:39489 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9335186 (8.9 MiB) TX bytes:10020863 (9.5 MiB) Memory:e0400000-e0420000
Setting up yum to use a disk based copy of the install DVD as its repository:
After installation, I copied the contents of the install DVD into a directory called /root/cdrom. Then I ran the command ‘createrepo .’ from the /root/cdrom directory. Note that I had to do a ‘rpm –install’ of the createrepo rpm before I could do this. I also created a file /etc/yum.repos.d/iso.repo with the following contents:
[iso_repository] baseurl=file:///root/cdrom enabled=1
One more step:
I ran the following on Oracle Linux:
# rpm --import /root/cdrom/RPM-GPG-KEY
I ran the following on CentOS 6:
# rpm --import /root/cdrom/RPM-GPG-KEY-CentOS-6
Now, yum can find rpms from the /root/cdrom directory.
Starting to install RHEL6 in a newly created blank VM using the libvirt command line tool virt-install:
First, I turned off the firewall using ‘/etc/init.d/iptables stop’, since I want to connect to the guest console using vncviewer from my desktop. Remember, this server is running headless.
# mkdir -p /vms/1 # virt-install --name=el6guest --arch=x86_64 --ram=512 --os-type=linux --os-variant=rhel6 --hvm --network bridge=br0 --cdrom=/dev/cdrom --disk path=/vms/1/vdisk0,size=16 --accelerate --vnc --vnclisten=0.0.0.0 Starting install... Creating storage file vdisk0 | 16 GB 00:00 Creating domain... | 0 B 00:00 Cannot open display: Run 'virt-viewer --help' to see a full list of available command line options Domain installation still in progress. You can reconnect to the console to complete the installation process.
Connecting to the console of the newly created VM in order to start installation:
The VM el6guest has now been created by virt-install, but we dont yet know which vnc port the guest is listening on. Run the command virsh as follows:
[root@localhost ~]# virsh vncdisplay el6guest :0
The ‘:0’ printed out by virsh tells us that the vnc server for guest el6guest is listening on port 5900, i.e. display 0
Startup the vncviewer binary on your desktop, and connect to the VM server at display 0. The Oracle Linux installer console will come up in vncviewer.
I installed a base server with root password el6guest. Once installation is complete, hit restart. The VM will shutdown at this point. You can restart the VM from virsh as shown below:
[root@localhost qemu]# virsh Welcome to virsh, the virtualization interactive terminal. Type: 'help' for help with commands 'quit' to quit virsh # start el6guest Domain el6guest started virsh # vncdisplay el6guest :0
Now, you can connect to display 0 using a vncviewer from your desktop, and the VM’s console will show up. That’s all folks..